1.1.5 Electron Configuration | AQA A Level Chemistry Revision Notes 2017 (2024)

• The Periodic Table is split up into four main blocks depending on their electron configuration
• Elements can be classified as an s-block element, p-block element and so on, based on the position of the outermost electron:
  • s block elements
    • Have their valence electron(s) in an s orbital
  • p block elements
    • Have their valence electron(s) in a p orbital
  • d block elements
    • Have their valence electron(s) in a d orbital
  • f block elements
    • Have their valence electron(s) in an f orbital

• The principal quantum shells increase in energy with increasing principal quantum number
  • E.g. n = 4 is higher in energy than n = 2
• The subshells increase in energy as follows: s ＜ p ＜ d ＜ f
  • The only exception to these rules is the 3d orbital which has slightly higher energy than the 4s orbital
  • Because of this, the 4s orbital is filled before the 3d orbital
• All the orbitals in the same subshell have the same energy and are said to be degenerate
  • E.g. p_x, p_y and p_z are all equal in energy

Relative energies of the shells and subshells

• The electron configuration gives information about the number of electrons in each shell, subshell and orbital of an atom
• The subshells are filled in order of increasing energy

The electron configuration shows the number of electrons occupying a subshell in a specific shell

• Writing out the electronconfiguration tells us how the electrons in an atom or ion are arranged in their shells, subshells and orbitals
• This can be done using the full electron configuration or the shorthand version
  • The full electron configuration describes the arrangement of all electrons from the 1s subshell up
  • The shorthand electron configuration includes using the symbol of the nearest preceding noble gas to account for however many electrons are in that noble gas
• Ions are formed when atoms lose or gain electrons
  • Negative ions are formed by adding electrons to the outer subshell
  • Positive ions are formed by removing electrons from the outer subshell
  • The transition metals fill the 4s subshell before the 3d subshell but lose electrons from the 4s first and not from the 3d subshell (the 4s subshell is lower in energy

Full Electron Configurations

• Hydrogen has 1 single electron
  • The electron is in the s orbital of the first shell
  • Its electron configuration is 1s¹
• Potassium has 19 electrons
  • The first 2 electrons fill the s orbital of the first shell
  • They then continue to fill subsequent orbitals and subshells in order of increasing energy
  • The 4s orbital is lower in energy than the 3d subshell, so it is therefore filled first
  • The full electron configuration of potassium is 1s² 2s² 2p⁶ 3s² 3p⁶ 4s¹

Shorthand Electron Configurations

• Using potassium as an example again:
  • The nearest preceding noble gas to potassium is argon
  • This accounts for 18 electrons of the 19 electrons that potassium has
  • The shorthand electron configuration of potassium is [Ar] 4s¹

Exceptions

• Chromium and copper have the following electron configurations, which are different to what you may expect:
  • Cr is [Ar] 3d⁵ 4s¹ not [Ar] 3d⁴ 4s²
  • Cu is [Ar] 3d¹⁰ 4s¹ not [Ar] 3d⁹ 4s²
• This is because the [Ar] 3d⁵ 4s¹ and [Ar] 3d¹⁰ 4s¹ configurations are energetically stable

Presenting the Electron Configuration

• Electrons can be imagined as small spinning charges which rotate around their own axis in either a clockwise or anticlockwise direction
• • The spin of the electron is represented by its direction
• Electrons with similar spin repel each other which is also called spin-pair repulsion
• Electrons will therefore occupy separate orbitals in the same subshell where possible, to minimize this repulsion and have their spin in the same direction
  • E.g. if there are three electrons in a p subshell, one electron will go into each p_x, p_y and p_z orbital

Electron configuration: three electrons in a p subshell

• Electrons are only paired when there are no more empty orbitals available within a subshell, in which case the spins are the opposite spins to minimize repulsion
  • E.g. if there are four electrons in a p subshell, one p orbital contains 2 electrons with opposite spin and two orbitals contain one electron only
  • The first 3 electrons fill up the empty p orbitals one at a time, and then the 4th one pairs up in thep_x orbital

Electron configuration: four electrons in a p subshell

Box Notation

• The electron configuration can be represented using the electrons in boxes notation
• Each box represents an atomic orbital
• The boxes are arranged in order of increasing energy from bottom to top
• The electrons are represented by opposite arrows to show the spin of the electrons
  • E.g. the box notation for titanium is shown below
  • Note that since the 3d subshell cannot be either full or half full, the second 4s electron is not promoted to the 3d level and stays in the 4s orbital

The electrons in titanium are arranged in their orbitals as shown. Electrons occupy the lowest energy levels first before filling those with higher energy